← Back to Blog

Is Home Automation Safe? Wiring, Wi-Fi and RF Health Facts

A client building a new home asked us a very reasonable question: "With all this Cat6 wiring and the automation equipment in our home, is there any health risk or radiation impact for our family? Are there any studies that show automation does not affect health?" Many families wonder the same, so we looked at what the major health bodies, the international safety limits and the equipment makers actually say, and put it in one place.

The short answer

A wired system emits no radio waves. Cat6 and control cables carry low-voltage signals, and the fields from the mains wiring that every home already has are far larger.

Professional wireless devices (Crestron, Lutron, KNX RF) operate far below the international safety limits. They transmit only briefly, and their makers advise keeping the antenna at least 20 cm from people.

More cables in the walls does not mean more exposure. What counts is the voltage and current a cable carries and the distance from it, and control cables carry very little.

The World Health Organization found no convincing evidence that the weak signals from wireless networks harm health. No one can honestly promise "never" about anything, but at these levels there is no evidence of harm.

Two kinds of "radiation"

The word "radiation" covers very different things. X-rays and gamma rays are ionising radiation: they carry enough energy to damage cells directly. The radio waves used by Wi-Fi, phones and wireless switches, and the fields around electric wiring, are non-ionising. They do not carry enough energy to break chemical bonds. WHO notes that the only health effect from radio-frequency fields identified in scientific reviews is a rise in body temperature from very high field strengths, found only in places such as industrial radio-frequency heaters. The levels from base stations and wireless networks are so low that the temperature increase is insignificant.

The wired system: Cat6 and control cables

A wired system is the simplest case, because a cable does not broadcast. Cat6 carries low-voltage data signals, and even Power over Ethernet stays in the safety extra-low voltage class. A KNX, Crestron or Lutron control cable carries a small voltage and a trickle of current. In each twisted pair the two wires carry equal and opposite currents, which makes their fields largely cancel.

Wired keypad: the signal stays inside the cable Panel Radio waves leaving the wall: none Wireless keypad: a brief signal only when pressed Processor Silent the rest of the time An illustration; the burst is shown larger than life
Wired or wireless, the idea is the same. A cable keeps its signal inside. A wireless keypad sends a very brief low-power signal when someone presses a button, and nothing in between.

The fields you do find in a home come mainly from the mains wiring and appliances, which exist in every house whether or not it has automation. WHO's Fact Sheet 322 reports that typical average magnetic fields in homes are about 0.07 µT in Europe and 0.11 µT in North America. Studies that suggested a small rise in childhood leukaemia looked at average exposures above 0.3 to 0.4 µT, and WHO's expert group concluded that the evidence is not strong enough to be considered causal. The international public limit is 200 µT.

The magnetic field of the mains wiring in your walls International limit for the public (ICNIRP)200 µTDirectly under a power lineabout 20 µTAverage level linked to a small rise in child leukaemia in some studies0.3 to 0.4 µTTypical average inside homes (Europe, North America)0.07 to 0.11 µT0.010.11101001000Magnetic field at mains frequency, microtesla (log scale)
Control cables are not the source. The fields in a home come mostly from mains wiring and appliances. Cat6 and control cables carry only a tiny current, so their fields are far smaller than the mains wiring every home already has. Values from WHO Fact Sheet 322 and the ICNIRP guidelines.

"But an automated home has many more cables. Does that add up?"

This is the worry we hear most from families planning automation: "There will be many more cables running through the walls and ceilings than in a normal home. Does that create a health hazard?" It is a fair question, and the answer comes from how electric and magnetic fields work. They depend on how much voltage and current a cable carries, and on how far you are from it, not on how many cables there are. The UK government's guidance puts it simply: electric fields get bigger as voltage increases, and the larger the current, the stronger the magnetic field.

A normal home: mains runs to every wall switch Board Switch Lamp mains at the switch An automated home: the keypad is low voltage Panel Lamp Keypad thin low-voltage control cable
The same lamp uses the same electricity. With automation the switching moves to the panel, and the wall keypad needs only a thin control cable. In a typical central design there is less mains cable at the wall switch, not more.
Current: the control cable vs the circuit it switches A switching module, drawing from the control cableabout 10 mAThe circuits that same module switches (rating)up to 20 A each0.001 A0.01 A0.1 A1 A10 A100 ACurrent in amperes (log scale)
About 2,000 times less. Magnetic fields follow current. In Siemens' KNX cabinet data sheet, a relay module draws about 10 mA from the 29 V control cable and each of its eight outputs is rated at 20 A. The rating is the most it can switch, not what your lights use.

For perspective, the UK government reports that the typical background magnetic field in homes is 0.01 to 0.2 µT, that the highest fields in homes occur close to appliances and the electrical wiring, even inside the walls, and that the effects it describes happen at levels many thousands of times higher than those encountered in buildings. That is true of every home, automated or not.

What does matter is the quality of the installation. Fields around correctly wired cables are small because the current going out and the current coming back run together and largely cancel. Faulty or incorrect wiring can break that balance and raise the field in a house, which is a known cause of higher readings. That is one more reason to use qualified installers, and one of the four things a reliable system depends on; see the four pillars of reliable automation.

The wireless system: Crestron, Lutron and Wi-Fi

Wireless devices do emit radio waves, as do your phone, your television remote and your router. What matters is how much, how often, and from what distance.

How much of the safety limit do home devices use? Safety guideline limit (ICNIRP, general public)100%Wi-Fi router, 0.5 m awayabout 0.7%Wi-Fi router, 1 m awayabout 0.1%Mobile mast exposure in homes (WHO survey range)0.002% to 2%Wired keypad and cableno radio signal0.001%0.01%0.1%1%10%100%Share of the international safety guideline (log scale)
Far below the limit. WHO surveys put mobile-mast exposure at 0.002% to 2% of the guideline. The Wi-Fi bars are calculated from the typical field strengths published by Ireland's EPA (about 2 V/m at 1 m and 5 V/m at 0.5 m, against a limit of 61 V/m; power goes with the square of field strength). The scale is logarithmic: each step is ten times larger.

Those 20 cm figures are the distance at which compliance is evaluated, and a wall keypad is used at arm's length, not against the head. Distance is the strongest protection of all: the strength of a radio signal falls with the square of the distance.

Drag to move away from a wireless device and see how fast the signal falls.

20 cm
Distance from the device20 cm
Signal strength compared with 20 cm100%

Distance is the strongest protection. In open space the strength of a radio signal falls with the square of the distance: twice as far means a quarter. Both Crestron and Lutron advise keeping the antenna at least 20 cm from people during prolonged use. This is a simplified illustration.

What the research says, honestly

SourceWhat it found
WHO, Base stations and wireless technologies"No convincing scientific evidence that the weak RF signals from base stations and wireless networks cause adverse health effects." Mast exposures range from 0.002% to 2% of the international guidelines, and the studies that found no effects used exposures about 1,000 times higher than home exposures.
WHO-commissioned review, 2024A systematic review of more than 5,000 studies found no association between mobile phone radio exposure and brain cancer. A 2025 follow-up on other cancers also found no association, with less certainty.
ICNIRP guidelines, 2020International limits for radio-frequency exposure with built-in safety margins, which cover Wi-Fi, Zigbee and similar devices.
WHO Fact Sheet 322, power-frequency fieldsTypical home averages of 0.07 to 0.11 µT; the evidence on childhood leukaemia above 0.3 to 0.4 µT is not strong enough to be considered causal.
Ireland's EPA, Wi-FiTypical indoor Wi-Fi levels are well below the recommended limits; no established evidence of harm at these levels, including for children.

For completeness, here is the other side. In 2011 the International Agency for Research on Cancer (IARC) classed radio-frequency fields as Group 2B, "possibly carcinogenic", meaning the evidence was limited and a risk could not be ruled out. The same group includes aloe vera whole-leaf extract and pickled vegetables. The 2024 WHO-commissioned review was done to update that picture, and it drew on a much larger body of research. Those studies concern mobile phones held against the head, whose exposure is far higher than anything installed on a wall. WHO is preparing a new assessment, and research continues.

So what can we honestly say? We cannot promise that anything will "never" have any effect on anyone, and no honest scientist would. What we can say is that the exposure from a wired automation system is essentially nil, that wireless devices from the established makers operate at a small fraction of the limits, and that the major reviews have found no evidence of harm at these levels.

Who sets the limits

The International Commission on Non-Ionizing Radiation Protection (ICNIRP) publishes the limits that most countries follow. For the general public, between 400 MHz and 2 GHz the reference level is the frequency in megahertz divided by 200, in watts per square metre, and above 2 GHz it is 10 W/m². They include safety margins well below the level at which any effect is established. India goes further for mobile towers: since 1 September 2012 the Department of Telecommunications has applied limits one-tenth of ICNIRP's to base station emissions, as a precaution. That rule is about towers, not indoor devices, but it shows how cautious the regulator is.

What matters more: the devices and frequencies in any home

Whether or not a home is automated, it is full of devices that produce fields at various frequencies: the phones in our hands, the oven and the hob in the kitchen, the wiring in the walls, the Wi-Fi router. Automation adds very little to that list. Here is the whole picture, by frequency, so you can see what matters and where a little care is worth it.

Tap a frequency to see what produces it in any home, what automation adds, and what matters most.

Most of what is in this picture is in every home. Automation adds little to any band, and nothing of note at 20 to 100 kHz.

The most useful thing to understand is closeness. The strength of a source falls away steeply with distance, so what you hold against your body counts for far more than what is across the room.

How close are you to each source? Phone held to the headtouchingHair dryer5 to 15 cmInduction hob, standing at it10 to 40 cmMicrowave oven, standing near it30 to 60 cmWireless wall keypad, when pressedarm's length, brieflyWi-Fi router across the room1 to 5 mMobile masttens to hundreds of m1 cm10 cm1 m10 m100 m1 kmDistance from your body (log scale, illustrative typical use)
Closeness matters more than anything else. Signal strength falls steeply with distance, so the sources you hold or stand beside count for far more than the ones across the room or on a wall. Amber items are in every home; teal is added by automation. The distances are typical and illustrative.

A rough order, from closest and strongest to furthest and weakest

SourceWhereWhy it ranks here
1. A mobile phone held to the headEvery homeIt is in contact with the body. Ireland's EPA says exposure from a phone in contact with the body can reach 100 to 400 times the typical exposure from a phone mast. The limit is 2 W/kg of tissue.
2. Induction hob, hair dryer and other heavy-current appliances used close upEvery homeMagnetic fields are highest very close to the source. Hobs usually meet the 27 µT reference level at common distances but can reach it close up (German BfS); the UK government reports up to a few tens of µT very close to appliances.
3. A microwave ovenEvery homeLeakage is capped at 5 mW per square centimetre at about 5 cm for the life of the oven, and falls to about one hundredth at 50 cm (FDA). A damaged oven can leak.
4. Cordless phone, Bluetooth headsetEvery homeA cordless (DECT) phone peaks at 250 mW but averages at most 10 mW (German BfS). Bluetooth is 2.5 mW for Class 2 devices, up to 100 mW for Class 1.
5. Wi-Fi router, mobile mastsEvery homeAt a distance: about 0.1 to 0.7% of the safety limit for Wi-Fi, 0.002% to 2% for masts.
6. Wireless automation devicesAdded by automationBrief, low-power signals only when a button is pressed or a command is sent, from devices the makers advise keeping 20 cm from people.
7. Wired automation cablingAdded by automationNo radio signal, and a tiny current at safety extra-low voltage.

This is an order of closeness and strength, not of danger. Every item above is designed and regulated to stay within the limits, and none has been shown to cause harm when used normally.

Small habits matter more than anything we install

So the honest summary for a family planning automation is this: the largest exposure in any home is the phone in your hand, not the switch on your wall. A wired automation system adds no radio exposure at all, and a wireless one adds a few brief, low-power signals.

How we plan a system with this in mind

This article is general information from published sources, not medical advice. For questions about a particular health condition or medical device, speak to your doctor.

Sources

Planning a home and want it done with this in mind?

Tell us your concerns when you share your plans. We will recommend a wired-first system and explain exactly where any wireless device would sit, at no obligation.

Talk to Agrima

Frequently Asked Questions

What matters more for my family's exposure: automation or the devices I already own?

The devices you already own, by a wide margin. The largest exposure in any home is a mobile phone held against the head, which can reach 100 to 400 times the typical exposure from a phone mast. Close-up appliances such as induction hobs, hair dryers and microwave ovens come next. A wired automation system adds no radio exposure, and a wireless one adds a few brief, low-power signals. Simple habits such as using the speaker on calls matter more than anything installed in the walls.

Does an automated home have more cables in the walls and ceilings, and is that a health risk?

More cables does not mean more exposure. What counts is the voltage and current a cable carries, and how far you are from it. Control cabling runs at 29 V DC or lower, in the safety extra-low voltage class, and a switching module draws about 10 mA from it, while the lighting circuits that module switches are rated at up to 20 A and exist in every home. The fields around correctly installed wiring are small and fall away quickly with distance. They rise mainly with faulty wiring, which is why we use qualified installers and keep the panel away from beds.

Is Cat6 network cabling in the walls harmful to health?

No evidence suggests so. Cat6 carries low-voltage data signals, and even Power over Ethernet stays within the 'safety extra-low voltage' class. The two wires in each twisted pair carry equal and opposite currents, so their fields largely cancel. The mains wiring that every home already has produces far larger magnetic fields than control and data cabling, and WHO reports that typical average fields in homes are about 0.07 to 0.11 microtesla.

Do Crestron and Lutron wireless devices emit radiation?

Every wireless device emits radio waves, as do phones, Wi-Fi routers and television remote controls. These are non-ionising radio waves, not the ionising radiation of X-rays. Both makers state in their documents that their products comply with the radio exposure limits, and advise keeping the antenna at least 20 cm from people during prolonged use. Lutron's Clear Connect devices also transmit only briefly, when a button is pressed or a command is sent.

Is Wi-Fi safe for children and for bedrooms?

WHO's review concluded there is no convincing scientific evidence that the weak signals from wireless networks cause adverse health effects, and Ireland's EPA reports typical indoor Wi-Fi levels of about 2 V/m at 1 metre against a limit of 61 V/m. As a precaution we place access points on ceilings, in the open, and not at the head of a bed. If you would like even lower exposure, a wired connection is always an option.

Is there a study that proves wireless automation is completely safe?

No scientific body claims absolute proof of safety for anything, and we do not either. What the evidence shows is that exposure from home wireless devices is a small fraction of international safety limits, that large reviews have not found harm at these levels, and that the only established effect of radio waves is heating at far higher exposures than anything in a home. Research continues, and WHO is preparing a new assessment.

What about the IARC 'possibly carcinogenic' classification?

In 2011 IARC placed radiofrequency fields in Group 2B, 'possibly carcinogenic', meaning the evidence was limited and could not rule out a risk. The same group includes aloe vera whole-leaf extract and pickled vegetables. A later WHO-commissioned systematic review of over 5,000 studies, published in 2024, found no association between mobile phone use and brain cancer. Mobile phones are held against the head, so their exposure is much higher than anything on a wall.

Does wired automation expose us to less radiation than wireless?

A wired keypad does not transmit radio waves at all, so it adds no radio exposure. That is one more reason we recommend a wired system, alongside reliability. Wireless devices still operate far below the limits.

Is it safe for someone with a pacemaker or other implant?

Anyone with an implanted medical device should follow the advice of their doctor and the device maker, who usually recommend keeping wireless devices a short distance away from the implant. We are happy to plan the system with this in mind, for example by choosing wired devices where the person sits or sleeps.

Health Radiation EMF Wi-Fi Cat6 Wireless

Garveshh Bharania is a co-founder of Agrima Solutions, a Crestron, Lutron and KNX integrator with offices in Ahmedabad and Rajkot. In 2026 he won the Excellence Award in the Residential Villa – System Integrator category at the Smart Space Awards, Smart Home Expo Mumbai.

Talk to Agrima about a project